View NCP1595CMNTWG_7040822.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2013 april, 2013 ? rev. 10 1 publication order number: ncp1595/d ncp1595, ncp1595a, ncp1595c 1 mhz, 1.5 a synchronous buck regulator the ncp1595/a/c family are fixed 1 mhz, high ? output ? current, synchronous pwm converters that integrate a low ? resistance, high ? side p ? channel mosfet and a low ? side n ? channel mosfet. the ncp1595/a/c utilizes current mode control to provide fast transient response and excellent loop stability. it regulates input voltages from 4.0 v to 5.5 v down to an output voltage as low as 0.8 v and is able to supply up to 1.5 a. the ncp1595/a/c includes an internally fixed switching frequency (f sw ), and an internal soft ? start to limit inrush currents. using the en pin, shutdown supply current is reduced to 3 a maximum. other features include cycle ? by ? cycle current limiting, short ? circuit protection and thermal shutdown. features ? input voltage range: from 4.0 v to 5.5 v ? internal 140 m high ? side switching p ? channel mosfet and 90 m low ? side n ? channel mosfet ? fixed 1 mhz switching frequency ? cycle ? by ? cycle current limiting ? overtemperature protection ? internal soft ? start ? diode emulation during light load (disabled for ncp1595c) ? hiccup mode short ? circuit protection ? start ? up with pre ? biased output load ? adjustable output voltage down to 0.8 v ? these are pb ? free devices applications ? dsp power ? hard disk drivers ? computer peripherals ? home audio ? set ? top boxes ? networking equipment ? lcd tv ? wireless and dsl/cable modem ? usb power devices device package shipping ? ordering information ncp1595mnr2g dfn6 (pb ? free) 3000 / tape & reel ncp1595mnt2g dfn6 case 506ah marking diagram http://onsemi.com 1 xxxxx = n1595, 1595a, 1595c a = assembly location l = wafer lot y = year w = work week = pb ? free package ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our t ape and reel packaging specifications brochure, brd8011/d. nc vcc vccp fb gnd lx 1 2 3 6 5 4 ncp1595/ncp1595c en vcc vccp fb gnd lx 1 2 3 6 5 4 ncp1595a pin connections ncp1595amnr2g ncp1595amntwg (note: microdot may be in either location) xxxxx alyw NCP1595CMNTWG
ncp1595, ncp1595a, ncp1595c http://onsemi.com 2 block diagram figure 1. block diagram ? + + + ? soft ? start power reset uvlo thd hiccup gm pwm control logic osc + ? ca + ncp1595/a/c vccp lx gnd vcc nc/en fb vref pmos m1 pin descriptions pin no symbol description 1 fb feedback input pin of the error amplifier. connect a resistor divider from the converter?s output voltage to this pin to set the converter?s output voltage. 2 gnd ground pin. connect to thermal pad. 3 lx the drains of the internal mosfets. the output inductor should be connected to this pin. 4 v ccp power input for the power stage 5 v cc input supply pin for internal bias circuitry. a 0.1 f ceramic bypass capacitor is preferred to connect to this pin. 6 nc no connection for ncp1595 or ncp1595c en logic input to enable the part. logic high to turn on the part and logic low to shut off the part. an internal pullup forces the part into an enable state when no external bias is present on the pin. for ncp1595a only ep pad exposed pad of the package provides both electrical contact to the ground and good thermal contact to the pcb. this pad must be soldered to the pcb for proper operation.
ncp1595, ncp1595a, ncp1595c http://onsemi.com 3 application circuit figure 2. ncp1595/a/c vccp vcc nc/en lx gnd fb v in 4.0 v ? 5.5 v v out absolute maximum ratings rating symbol value unit power supply pin (pin 4, 5) to gnd v in 6.5 ? 0.3 (dc) ? 1.0 (t < 100 ns) v lx to gnd lx v in + 0.7 v in + 1.0 (t < 20 ns) ? 0.7 (dc) ? 5.0 (t < 100 ns) v all other pins 6.0 ? 0.3 (dc) ? 1.0 (t < 100 ns) v operating temperature range t a ? 40 to +85 c junction temperature t j ? 40 to +150 c storage temperature range t s ? 55 to +150 c thermal resistance junction ? to ? air (note 1) r ja 68.5 c/w stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. 1. r ja measured on approximately 1x1 inch sq. of 1 oz. copper.
ncp1595, ncp1595a, ncp1595c http://onsemi.com 4 electrical characteristics (v in = 4.0 v ? 5.5 v, v out = 1.2 v, t j = +25 c for typical value; ? 40 c < t a < 85 c for min/max values unless noted otherwise) parameter symbol test conditions min typ max unit v in input voltage range (note 2) v in 4.0 5.5 v v cc uvlo threshold 3.2 3.5 3.8 v uvlo hysteresis 335 mv v cc quiescent current i invcc v in = 5 v,v fb = 1.5 v, (no switching) 1.7 2.0 ma v ccp quiescent current i invccp v in = 5 v,v fb = 1.5 v, (no switching) 25 a v in shutdown supply current (note 3) i qshdn (ncp1595a), en = 0 v 1.8 3.0 a feedback voltage reference voltage v fb 0.788 0.800 0.812 v feedback input bias current (note 2) i fb v fb = 0.8 v 10 100 n a feedback voltage line regulation (note 3) v in = 4.0 v to 5.5 v 0.06 %/v pwm maximum controllable duty cycle (regulating) 82 85 % minimum controllable on time (note 3) 50 ns pulse ? by ? pulse current limit pulse ? by ? pulse current limit (regulation) i lim 2.7 3.9 4.3 a pulse ? by ? pulse current limit (soft ? start) i limss 4.0 5.3 6.1 a oscillator oscillator frequency f sw 0.87 1.0 1.13 mhz mosfet high side mosfet on resistance (note 2) r ds(on) hs r ds(on) hs i ds = 100 ma, v gs = 5 v 140 200 m high side mosfet leakage (note 3) v en = 0 v, v sw = 0 v 10 a low side mosfet on resistance (note 2) r ds(on) ls r ds(on) ls i ds = 100 ma, v gs = 5 v 90 125 m low side mosfet leakage (note 3) v en = 0 v, v sw = 5 v 10 a enable (ncp1595a) en hi threshold enhi (ncp1595a) 1.4 v en lo threshold enlo (ncp1595a) 0.4 v en hysteresis (ncp1595a) 200 mv en pullup current (ncp1595a) 1.4 3.0 a soft ? start soft ? start ramp time (note 3) t ss f sw = 1 mhz 1.0 ms hiccup timer (note 3) 2.0 ms thermal shutdown thermal shutdown threshold (note 3) 185 c thermal shutdown hysteresis (note 3) 40 c 2. guaranteed by characterization. not production tested. 3. guaranteed by design. not production tested.
ncp1595, ncp1595a, ncp1595c http://onsemi.com 5 typical operating characteristics t a , ambient temperature ( c) 3.1 3.2 3.3 3.4 3.5 3.7 ? 40 10 35 85 figure 3. undervoltage lockout vs. temperature uvlo (v) figure 4. feedback input threshold vs. temperature 785 790 795 800 805 810 815 ? 40 10 35 85 t a , ambient temperature ( c) v fb , fb input threshold (v) figure 5. switching frequency vs. temperature 0.7 0.8 0.9 1.0 1.1 1.2 1.3 ? 40 10 35 85 t a , ambient temperature ( c) f sw , switch frequency (mhz) figure 6. current limit vs. temperature 3.5 4.0 4.5 5.0 5.5 6.0 ? 40 10 35 85 t a , ambient temperature ( c) i lim , current limit (a) 1.0 1.2 1.4 1.6 1.8 2.0 ? 40 10 35 85 t a , ambient temperature ( c) i cc , switching (ma) figure 7. quiescent current into v cc vs. temperature figure 8. quiescent current into v cc vs. temperature uvlo falling threshold 3.6 60 ? 15 uvlo rising threshold ? 15 60 60 ? 15 ? 15 60 i lim (regulation) i lim (soft ? start) ? 15 60 1.0 1.2 1.4 1.6 1.8 2.0 ? 40 10 35 85 t a , ambient temperature ( c) i cc , disabled ( a) ? 15 60
ncp1595, ncp1595a, ncp1595c http://onsemi.com 6 typical operating characteristics figure 9. load regulation for v out = 3.3 v figure 10. efficiency vs. output current for v out = 3.3 v figure 11. load regulation for v out = 1.8 v figure 12. efficiency vs. output current for v out = 1.8 v figure 13. load regulation for v out = 1.2 v 1.10 1.12 1.14 1.16 1.18 1.20 1.22 0.1 0.7 1.0 1.5 v in = 4.0 v v in = 5.0 v 20 40 50 60 70 80 90 100 0.01 0.1 1 10 v out , output voltage (v) 0 i out , output current (a) i out , output current (a) v in = 5.0 v v in = 4.0 v efficiency (%) figure 14. efficiency vs. output current for v out = 1.2 v 1.24 1.26 1.28 1.30 0.2 0.3 0.4 0.5 0.6 0.8 0.9 1.1 1.2 1.3 1.4 1.70 1.72 1.74 1.76 1.78 1.80 1.82 0.1 0.7 1.0 1.5 v in = 4.0 v v in = 5.0 v v out , output voltage (v) 0 i out , output current (a) 1.84 1.86 1.88 1.90 0.2 0.3 0.4 0.5 0.6 0.8 0.9 1.1 1.2 1.3 1.4 3.20 3.22 3.24 3.26 3.28 3.30 3.32 0.1 0.7 1.0 1.5 v in = 4.0 v v in = 5.0 v v out , output voltage (v) 0 i out , output current (a) 3.34 3.36 3.38 3.40 0.2 0.3 0.4 0.5 0.6 0.8 0.9 1.1 1.2 1.3 1.4 30 20 40 50 60 70 80 90 100 0.01 0.1 1 10 i out , output current (a) v in = 5.0 v v in = 4.0 v efficiency (%) 30 20 40 50 60 70 80 90 100 0.01 0.1 1 10 i out , output current (a) v in = 5.0 v v in = 4.0 v efficiency (%) 30 v out = 1.2 v l = 3.3 h c out = 2 x 22 f v out = 1.8 v l = 3.3 h c out = 2 x 22 f v out = 3.3 v l = 3.3 h c out = 2 x 22 f v out = 3.3 v l = 3.3 h c out = 2 x 22 f v out = 1.8 v l = 3.3 h c out = 2 x 22 f v out = 1.2 v l = 3.3 h c out = 2 x 22 f
ncp1595, ncp1595a, ncp1595c http://onsemi.com 7 (v in = 5 v, i load = 700 ma, l = 3.3 h, c out = 2 x 22 f) upper trace: l x pin switching waveform, 2 v/div middle trace: output ripple voltage, 20 mv/div lower trace: inductor current, 1 a/div time scale: 1.0 s/div (v in = 5 v, i load = 100 ma, l = 3.3 h, c out = 2 x 22 f) upper trace: l x pin switching waveform, 2 v/div middle trace: output ripple voltage, 20 mv/div lower trace: inductor current, 1 a/div time scale: 1.0 s/div figure 15. dcm switching waveform for v out = 3.3 v figure 16. ccm switching waveform for v out = 3.3 v (v in = 5 v, i load = 100 ma, l = 3.3 h, c out = 2 x 22 f) upper trace: l x pin switching waveform, 2 v/div middle trace: output ripple voltage, 20 mv/div lower trace: inductor current, 200 ma/div time scale: 1.0 s/div (v in = 5 v, i load = 400 ma, l = 3.3 h, c out = 2 x 22 f) upper trace: l x pin switching waveform, 2 v/div middle trace: output ripple voltage, 20 mv/div lower trace: inductor current, 1 a/div time scale: 1.0 s/div figure 17. dcm switching waveform for v out = 1.2 v figure 18. ccm switching waveform for v out = 1.2 v (v in = 5 v, i load = 100 ma, l = 3.3 h, c out = 2 x 22 f) upper trace: en pin voltage, 2 v/div middle trace: output voltage, 1 v/div lower trace: inductor current, 100 ma/div time scale: 500 s/div (v in = 5 v, i load = 100 ma, l = 3.3 h, c out = 2 x 22 f) upper trace: en pin voltage, 2 v/div middle trace: output voltage, 1 v/div lower trace: inductor current, 100 ma/div time scale: 500 s/div fi g ure 19. soft ? start waveforms for v out = 3.3 v fi g ure 20. soft ? start waveforms for v out = 1.2 v
ncp1595, ncp1595a, ncp1595c http://onsemi.com 8 (v in = 5 v, i load = 100 ma, l = 3.3 h, c out = 2 x 22 f) upper trace: output dynamic voltage, 100 mv/div lower trace: output current, 500 ma/div time scale: 200 s/div (v in = 5 v, i load = 100 ma, l = 3.3 h, c out = 2 x 22 f) upper trace: output dynamic voltage, 100 mv/div lower trace: output current, 500 ma/div time scale: 200 s/div (v in = 5 v, i load = 100 ma, l = 3.3 h, c out = 2 x 22 f) upper trace: output dynamic voltage, 100 mv/div lower trace: output current, 500 ma/div time scale: 200 s/div (v in = 5 v, i load = 100 ma, l = 3.3 h, c out = 2 x 22 f) upper trace: output dynamic voltage, 100 mv/div lower trace: output current, 500 ma/div time scale: 200 s/div figure 21. transient response for v out = 3.3 v figure 22. transient response for v out = 3.3 v figure 23. transient response for v out = 1.2 v figure 24. transient response for v out = 1.2 v
ncp1595, ncp1595a, ncp1595c http://onsemi.com 9 detailed description overview the ncp1595/a/c is a synchronous pwm controller that incorporates all the control and protection circuitry necessary to satisfy a wide range of applications. the ncp1595/a/c employs current mode control to provide fast transient response, simple compensation, and excellent stability. the features of the ncp1595/a/c include a precision reference, fixed 1 mhz switching frequency, a transconductance error amplifier, an integrated high ? side p ? channel mosfet and low ? side n ? channel mosfet, internal soft ? start, and very low shutdown current. the protection features of the ncp1595/a/c include internal soft ? start, pulse ? by ? pulse current limit, and thermal shutdown. reference voltage the ncp1595/a/c incorporates an internal reference that allows output voltages as low as 0.8 v. the tolerance of the internal reference is guaranteed over the entire operating temperature range of the controller. the reference voltage is trimmed using a test configuration that accounts for error amplifier offset and bias currents. oscillator frequency a fixed precision oscillator is provided. the oscillator frequency range is 1 mhz with 13% variation. transconductance error amplifier the transconductance error amplifier?s primary function is to regulate the converter?s output voltage using a resistor divider connected from the converter?s output to the fb pin of the controller, as shown in the applications schematic. if a fault occurs, the amplifier?s output is immediately pulled to gnd and pwm switching is inhibited. internal soft ? start to limit the startup inrush current, an internal soft start circuit is used to ramp up the reference voltage from 0 v to its final value linearly. the internal soft start time is 1 ms typically. output mosfets the ncp1595/a/c includes low r ds(on) , both high ? side p ? channel and low ? side n ? channel mosfets capable of delivering up to 1.5 a of current. when the controller is disabled or during a fault condition, the controller?s output stage is tri ? stated by turning off both the upper and lower mosfets. adaptive dead time gate driver in a synchronous buck converter, a certain dead time is required between the low side drive signal and high side drive signal to avoid shoot through. during the dead time, the body diode of the low side fet freewheels the current. the body diode has much higher voltage drop than that of the mosfet, which reduces the efficiency significantly. the longer the body diode conducts, the lower the efficiency. in ncp1595/a/c, the drivers and mosfets are integrated in a single chip. the parasitic inductance is minimized. adaptive dead time control method is used to prevent the shoot through from happening and minimizing the diode conduction loss at the same time. pulse width modulation a high ? speed pwm comparator, capable of pulse widths as low as 50 ns, is included in the ncp1595/a/c. the inverting input of the comparator is connected to the output of the error amplifier. the non ? inverting input is connected to the the current sense signal. at the beginning of each pwm cycle, the clk signal sets the pwm flip ? flop and the upper mosfet is turned on. when the current sense signal rises above the error amplifier?s voltage then the comparator will reset the pwm flip ? flop and the upper mosfet will be turned off. current sense the ncp1595/a/c monitors the current in the upper mosfet. the current signal is required by the pwm comparator and the pulse ? by ? pulse current limiter.
ncp1595, ncp1595a, ncp1595c http://onsemi.com 10 protections undervoltage lockout (uvlo) the under voltage lockout feature prevents the controller from switching when the input voltage is too low to power the internal power supplies and reference. hysteresis must be incorporated in the uvlo comparator to prevent ixr drops in the wiring or pcb traces from causing on/off cycling of the controller during heavy loading at power up or power down. overcurrent protection (ocp) ncp1595/a/c detects high side switch current and then compares to a voltage level representing the overcurrent threshold limit. if the current through the high side fet exceeds the overcurrent threshold limit for seven consecutive switching cycles, overcurrent protection is triggered. once the overcurrent protection occurs, hiccup mode engages. first, hiccup mode, turns off both fets and discharges the internal compensation network at the output of the ota. next, the ic waits typically 2 ms and then resets the overcurrent counter . after this reset, the circuit attempts another normal soft ? start. during soft ? start, the overcurrent protection threshold is increased to prevent false overcurrent detection while charging the output capacitors. hiccup mode reduces input supply current and power dissipation during a short circuit. it also allows for much improved system up ? time, allowing auto ? restart upon removal of a temporary short ? circuit. power save mode if the load current decreases, the converter can skip switching and operate with reduced frequency. this minimizes the quiescent current and maintains high efficiency. ncp1595c disables this feature. pre ? bias startup in some applications the controller will be required to start switching when it?s output capacitors are charged anywhere from slightly above 0 v to just below the regulation voltage. this situation occurs for a number of reasons: the converter?s output capacitors may have residual charge on them or the converter?s output may be held up by a low current standby power supply. ncp1595/a/c supports pre ? bias start up by holding switching off until the soft ? start ramp reaches the fb pin voltage. thermal shutdown the ncp1595/a/c protects itself from over heating with an internal thermal monitoring circuit. if the junction temperature exceeds the thermal shutdown threshold both the upper and lower mosfets will be shut off.
ncp1595, ncp1595a, ncp1595c http://onsemi.com 11 application information programming the output voltage the output voltage is set using a resistive voltage divider from the output voltage to fb pin (see figure 25). so the output voltage is calculated according to eq.1. v out v fb r 1 r 2 r 2 (eq. 1) figure 25. output divider fb r2 r1 v out inductor selection the inductor is the key component in the switching regulator. the selection of inductor involves trade ? offs among size, cost and efficiency. the inductor value is selected according to the equation 2. l v out f i ripple 1 v out v in(max) (eq. 2) where v out ? the output voltage; f ? switching frequency, 1.0 mhz; i ripple ? ripple current, usually it?s 20% ? 30% of output current; v in(max) ? maximum input voltage. choose a standard value close to the calculated value to maintain a maximum ripple current within 30% of the maximum load current. if the ripple current exceeds this 30% limit, the next larger value should be selected. the inductor?s rms current rating must be greater than the maximum load current and its saturation current should be about 30% higher. for robust operation in fault conditions (start ? up or short circuit), the saturation current should be high enough. to keep the efficiency high, the series resistance (dcr) should be less than 0.1 , and the core material should be intended for high frequency applications. output capacitor selection the output capacitor acts to smooth the dc output voltage and also provides energy storage. so the major parameter necessary to define the output capacitor is the maximum allowed output voltage ripple of the converter. this ripple is related to capacitance and the esr. the minimum capacitance required for a certain output ripple can be calculated by equation 4. c out(min) i ripple 8 f v ripple (eq. 3) where v ripple is the allowed output voltage ripple. the required esr for this amount of ripple can be calculated by equation 5. esr v ripple i ripple (eq. 4) based on equation 2 to choose capacitor and check its esr according to equat ion 3. if esr exceeds the value from eq.4, multiple capacitors should be used in parallel. ceramic capacitor can be used in most of the applications. in addition, both surface mount tantalum and through ? hole aluminum electrolytic capacitors can be used as well. maximum output capacitor ncp1595/a/c family has internal 1 ms fixed soft ? start and overcurrent limit. it limits the maximum allowed output capacitor to startup successfully. the maximum allowed output capacitor can be determined by the equation: c out(max) i lim(min) i load(max) i p ? p 2 v out t ss(min) (eq. 5) where t ss(min) is the minimum soft ? start period (1ms); d ipp is the current ripple. this is assuming that a constant load is connected. for example, with 3.3 v/2.0 a output and 20% ripple, the max allowed output capacitors is 546 f. input capacitor selection the input capacitor can be calculated by equation 6. c in(min) i out(max) d max 1 f v in(ripple) (eq. 6) where v in(ripple) is the required input ripple voltage. d max v out v in(min) is the maximum duty cycle. (eq. 7) power dissipation the ncp1595/a/c is available in a thermally enhanced 6 ? pin, dfn. when the die temperature reaches +185 c, the ncp1595/a/c shuts down (see the thermal ? overload protection section). the power dissipated in the device is the sum of the power dissipated from supply current (pq), power dissipated due to switching the internal power mosfet (p sw ), and the power dissipated due to the rms current through the internal power mosfet (pon). the total power dissipated in the package must be limited so the junction temperature does not exceed its absolute maximum rating of +150 c at maximum ambient temperature.
ncp1595, ncp1595a, ncp1595c http://onsemi.com 12 calculate the power lost in the ncp1595/a/c using the following equations: 1. high side mosfet the conduction loss in the top switch is: p hson i 2 rms_hsfet
r ds(on)hs (eq. 8) where: i rms_fet i out 2 i pp 2 12
d (eq. 9) i pp is the peak ? to ? peak inductor current ripple. the power lost due to switching the internal power high side mosfet is: p hssw v in i out t r t f f sw 2 (eq. 10) t r and t f are the rise and fall times of the internal power mosfet measured at sw node. 2. low side mosfet the power dissipated in the top switch is: p lson i rms_lsfet 2 r ds(on)ls (eq. 11) where: i rms_lsfet i out 2 i pp 2 12 ( 1 d ) (eq. 12) i pp is the peak ? to ? peak inductor current ripple. the switching loss for the low side mosfet can be ignored. the power lost due to the quiescent current (i q ) of the device is: p q v in i q (eq. 13) i q is the switching quiescent current of the ncp1595/a/c. p total p hson p hssw p lson p q (eq. 14) calculate the temperature rise of the die using the following equation: t j t c p total jc (eq. 15) jc is the junction ? to ? case thermal resistance equal to 1.7 c/w. t c is the temperature of the case and tj is the junction temperature, or die temperature. the case ? to ? ambient thermal resistance is dependent on how well heat can be transferred from the pc board to the air. solder the underside ? exposed pad to a large copper gnd plane. if the die temperature reaches +185 c the ncp1595/a/c shut down and does not restart again until the die temperature cools by 40 c. layout consideration as with all high frequency switchers, when considering layout, care must be taken in order to achieve optimal electrical, thermal and noise performance. for 1.0mhz switching frequency, switch rise and fall times are typically in few nanosecond range. to prevent noise both radiated and conducted the high speed switching current path must be kept as short as possible. shortening the current path will also reduce the parasitic trace inductance of approximately 25 nh/inch. at switch off, this parasitic inductance produces a flyback spike across the ncp1595/a/c switch. when operating at higher currents and input voltages, with poor layout, this spike can generate voltages across the ncp1595/a/c that may exceed its absolute maximum rating. a ground plane should always be used under the switcher circuitry to prevent interplane coupling and overall noise. the fb component should be kept as far away as possible from the switch node. the ground for these components should be separated from the switch current path. failure to do so will result in poor stability or subharmonic like oscillation. board layout also has a significant effect on thermal resistance. reducing the thermal resistance from ground pin and exposed pad onto the board will reduce die temperature and increase the power capability of the ncp1595/a/c. this is achieved by providing as much copper area as possible around the exposed pad. adding multiple thermal vias under and around this pad to an internal ground plane will also help. similar treatment to the inductor pads will reduce any additional heating effects.
ncp1595, ncp1595a, ncp1595c http://onsemi.com 13 package dimensions dfn6 3x3, 0.95p case 506ah issue o *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* ??? ??? ??? ??? c 0.15 2x 2x top view d e c 0.15 notes: 1. dimensions and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimesnion b applies to plated terminal and is measured between 0.25 and 0.30 mm from terminal. 4. coplanarity applies to the exposed pad as well as the terminals. 3.31 0.130 0.63 0.025 2.60 0.1023 0.450 0.0177 1.700 0.685 mm inches scale 10:1 0.950 0.0374 e2 bottom view b 0.10 6x l 13 0.05 c ab c d2 4x e k 64 6x 6x (a3) c c 0.08 6x c 0.10 side view a1 a seating plane dim min nom max millimeters a 0.80 0.90 1.00 a1 0.00 0.03 0.05 a3 0.20 ref b 0.35 0.40 0.45 d 3.00 bsc d2 2.40 2.50 2.60 e 3.00 bsc e2 1.50 1.60 1.70 e 0.95 bsc k 0.21 ??? ??? l 0.30 0.40 0.50 (note 3) on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. ncp1595/d publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5817 ? 1050 literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative

▲Up To Search▲

Price & Availability of NCP1595CMNTWG

	To Download NCP1595CMNTWG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .